Apr 02, 2016 TTL Serial Camera (CMOS) with Arduino Uno This tutorial shows how to make Adafruit’s CMOS camera work with an Arduino Uno (or equivalent) and write JPEG images to a microSD card. Note that I am using Linux Mint 17.1 operating system. May 04, 2015 This tutorial is for our new TTL serial camera module with NTSC video output. These modules are a nice addition to a microcontroller project when you want to take a photo or control a video stream. Learn Arduino, Lesson 5. The Serial Monitor Arduino Lesson 5. The Serial Monitor by Simon Monk. Learn Arduino, Lesson 2. LEDs Arduino Lesson 2.

May 02, 2017 What I am using is a TTL Jpeg Serial Camera connected to digital pins 2 and 3 and an SD Card breakout that connects to digital pins 10 through 13 on the arduino. Next up, we will wire the camera to our microcontroller (in this case an Arduino). This is pretty similar to the above except we will be using two digital pins and a software serial port to talk to the camera.

Let’s equip Arduino with a serial-interface JPEG Camera with IR and try two applications: the first one saves shots (on a SD-card) at regular intervals while the second uses a PIR sensor to detect intrusions and photograph what happens.

Recently, miniaturized cameras with serial communication interface have been launched on the market. Compared to traditional cameras, they offer easier integration with Arduino or other microcontroller-based boards.

It is quite easy to understand that using a composite or USB interface camera requires a considerable effort, on both hardware and software sides. If you decide to bet on a serial interface camera, everything gets easier, because all the prototyping boards (Arduino in particular) and all microcontrollers (Microchip, Atmel etc.) have at least one serial port as a standard feature.

The basic concept of these cameras is that you can send all the setup commands, take screenshots and viewing images through appropriate bytes sequences via their serial port.

In our case, we will use a LinkSprite camera connected to Arduino Uno. Special feature of this camera is the ability to capture images even at night; in fact, it has a brightness sensor and infrared LEDs activated automatically when the detected light falls below a certain threshold (refer to the pictures in these pages to get an idea of how infrared LEDs work).

The camera is capable of capturing high-resolution images, sending them as JPEG through the serial port. It has a four-pin connector where two pins are for the power supply (+ 5V and GND) and two for the serial port (RX and TX).

This article will show how to use this camera in two different Arduino projects: the first creates a timing system to take pictures on specific intervals, storing them on the SD-card, while the second is an automatic surveillance system activated only if the special PIR sensor (Passive Infrared Radar) detects a warm object moving in the camera view field. In practice, this second application is a time-lapse video surveillance device that records what happens in a room, activated by the detection of moving people or vehicles. Of course, the PIR detection area must match the same camera angle so that the captured images effectively show the triggering “foe”.

Images will be saved on a Sd-card in JPEG format file and therefore we need a dedicated Sd-card shield (available on Futura Elettronica).

Finally, we will use software libraries (JPEGCamera) developed by us specifically for these camera usage examples.

SYSTEM HARDWARE

About the first application, the hardware consists of an Arduino Uno Rev 3 and a SD-card shield used to save images, all connected to the serial camera. The SD shield has four jumpers allowing us to choose which Arduino pin works as “chip select” (you can choose between D4, D8, D9 and D10); for “chip select” we mean the command line that enables the shield.

In our examples, we use D4 therefore we have to insert the corresponding jumper.

The camera has a four-pin connector used for both power and serial interface, and is supplied with a four wires cable (colors: red, brown, purple and gray) ending with female jumpers. Please note that for the serial communication between Arduino and the camera we decided not to use the hardware serial port, but we use the software one (mapped on Arduino D2 and D3 pins); in this way, the software library keeps the hardware port free for debugging.

To connect Arduino to the camera you need to connect the red wire (RXD) to Arduino D3 pin; the brown (TXD) to D2; the gray to the + 5V signal and finally the violet to ground (GND).

For the second application, we must add the PIR sensor to the hardware just described. What we used for our prototype is a device with a certain “intelligence” on-board, which implements two different trigger modes, providing a programmable delay time (between the motion detection and the signal trigger ) ranging from 0.3 to 180 seconds, has a 120 ° detection angle and 7 meters maximum range. The sensor has three pins (TTL 0V – 3.3V output and positive-negative power supply). To connect Arduino you must create a three-wire cable where the power supply positive and negative pins must be connected to Arduino +5V and GND while the TTL output to Arduino D5 pin. Through the output, the device sends the trigger signal caused by PIR sensor movement detection.

ARDUINO LIBRARY

JPEGCamera

To allow Arduino managing the JPEG camera we have developed a library (JPEGCamera) that offers all the LinkSprite camera functions: initialization, screenshots capturing and saving images.

The library provides an object called JPEGCamera you can call for complete hardware management.

A Begin function initializes the entire camera management system, a Reset physically resets the camera, a setImageSize sets the captured image size (you can choose between 160 x 120, 320 x 280 and 640 x 480 pixels). Then there is the takePicture function , who commands the camera to capture the image currently framed (basically is the take screenshot function) and readJpegFileSize, which reads the size (in bytes) of the image file stored. Other functions include the readJpegFileContent, which deals with reading (a packet at a time) the image data and finally stopTakingPictures, which stops the screenshots capture.

The readJpegFileContent Bto plusdeck 2c software. function deserves a special mention: the data reading process works with a packet (64 bytes, in our case) at a time. To do this it is necessary, each time you call the procedure, to indicate the starting address (the first time is equal to 0, the second 64, the third 128 and so on) and the packet size to be read (in our case, always 64; please note that it is not possible to exceed that value). The function requires as input a byte array where data will be saved; also returns the iSend output parameter, which indicates if the reading operation has been completed.

SKETCH EXAMPLE 1

Ttl Serial Camera Arduino Uno

Starting from the beginning, we analyze the first JPEG camera example code, the continuous saving images application (Listing 1).

We include the necessary libraries (JPEGCamera.h,SoftwareSerial.h – since we will use a software serial interface – and SD.h, to save images on the SD-card) and define the size (in bytes) of a single data packet stored (chunk_size; 64 bytes).

Subsequently we define the Arduino pin (D4) we will use as SD-card chip select and some variables that we will use in the pr